conductive polymer aluminum solid electrolytic capacitors cr series chip type, high reliability specifications temperature characteristics (max.impedance ratio) category temperature range rated voltage range rated capacitance range capacitance tolerance tangent of loss angle (tan ) esr (1) leakage current ( 2) performance characteristics item 55 to +125? 6.3 to 100v 5.6 to 2700 f 20% at 120hz, 20? less than or equal to the specified value at 120hz, 20? less than or equal to the specified value at 100khz, 20? after 2 minutes' application of rated voltage, leakage current is not more than 0.03cv or 3( ? ), whichever is greater. z+125? / z+20? 1.25 (100khz) z 55? / z+20? 1.25 endurance shelf life esr after endurance (1) damp heat (steady state) resistance to soldering heat marking the specifications listed at right shall be met when the capacitors are restored to 20 ? after d.c. bias plus rated ripple current is applied for 4000 hours at 125?, the peak voltage shall not exceed the rated voltage. the specifications listed at right shall be met when the capacitors are restored to 20? after the rated voltage is applied for 1000 hours at 85?, 85% rh. less than or equal to the specified value at 100khz, -40? the specifications listed at right shall be met when the capacitors are restored to 20? after the rated voltage is applied for 1000 hours at 85?, 85% rh. after soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. pre-heating shall be done at 150 to 200? and for 60 to 180 sec. the duration for over +230? temperature at capacitor surface shall not exceed 60 seconds. in the case of peak temp, less than 250?, reflow soldering shall be two times maximum. in the case of peak temp, less than 260?, reflow soldering shall be once. measurement for solder temperature profile shall be made at the capacitor top and the terminal. navy blue print on the case top capacitance change tan leakage current ( 2) esr (1) within 20% of initial capacitance value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 20% of initial capacitance value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr (1) within 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value less than or equal to the initial specified value high reliability, high voltage (to 100v). low esr, high ripple current. long life of 4000 hours at 125?. smd type : lead free reflow soldering condition at 260? peak complete correspondence. adapted to the rohs directive (2011/65/eu). added esr specification after the test at -40?. 1 esr should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 conditioning : if any doubt arises, measure the leakage current after the voltage treatment of applying dc rated voltage continuously to the capacitor for 120 minutes at 105?. 3 initial value : the value before test of examination of resistance to soldering. p 1 c 2 r 3 1 4 v 5 1 6 5 7 1 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration taping code size code capacitance tolerance ( 20%) rated capacitance ( 150f ) rated voltage ( 35v ) series name type 6.3 8l, 8 7l, 8 10l, 10 10l : the vibration structure-resistant product is also available upon request, please ask for detail. cr 150 v 331 h 0.3 max. d0.5 b 0.2 a 0.2 c 0.2 0.5 max. e l series voltage (v:35v) plastic platform lot no. capacitance negative positive +0.1 -0.4 dimensions type numbering system (example : 35v 150f) dimension table in next page. d l a b c e h 5.0 5.9 6.0 5.3 5.3 1.6 0.5 to 0.8 size 5 6l 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 6.3 6l 6.3 7.9 7.3 6.6 6.6 2.1 0.5 to 0.8 6.3 8l 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 7l 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 10l 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 12l 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 10 8l 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 10 10l 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 10 12.7l (mm) code j v 6.3 a 10 c 16 d 20 e 25 v 35 h 50 j 63 k 80 2a 100 voltage cr high capacitance long life assurance cx cat.8100c
conductive polymer aluminum solid electrolytic capacitors cr series standard ratings rated voltage (v)(code) surge voltage (v) 900 1500 1800 1600 3700 3000 4000 3600 4700 800 1400 1700 1600 3500 2900 3800 3400 4500 800 1300 1700 1500 3400 2700 3800 3200 4300 700 1300 1700 1200 3300 2600 3500 3100 4200 700 1300 1600 1200 3200 2500 3300 3100 4100 600 1100 1500 1200 3100 2500 3300 3100 3900 83 48 30 38 23 27 21 23 17 90 51 33 42 24 30 23 26 18 98 54 35 45 26 33 24 29 20 105 62 38 59 29 35 27 30 21 113 65 41 62 30 36 29 30 23 120 72 47 66 33 38 32 30 24 55 32 20 25 15 18 14 15 11 60 34 22 28 16 20 15 17 12 65 36 23 30 17 22 16 19 13 70 41 25 39 19 23 18 20 14 75 43 27 41 20 24 19 20 15 80 48 31 44 22 25 21 20 16 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 180 330 560 560 1000 1200 1500 1800 2700 120 180 330 330 680 680 1000 1200 1500 68 120 220 220 470 470 560 680 1000 56 100 150 150 330 330 470 560 680 33 56 100 100 220 220 270 330 470 27 47 68 68 150 150 220 270 330 8 6.3 (0j) 13 10 (1a) 20 16 (1c) 25 20 (1d) 31 25 (1e) 43 35 (1v) pcr0j181mcl1gs pcr0j331mcl1gs pcr0j561mcl4gs pcr0j561mcl1gs pcr0j102mcl1gs pcr0j122mcl1gs pcr0j152mcl1gs pcr0j182mcl1gs pcr0j272mcl1gs pcr1a121mcl1gs pcr1a181mcl1gs pcr1a331mcl4gs pcr1a331mcl1gs pcr1a681mcl6gs pcr1a681mcl1gs pcr1a102mcl1gs pcr1a122mcl1gs pcr1a152mcl1gs pcr1c680mcl1gs pcr1c121mcl1gs pcr1c221mcl4gs pcr1c221mcl1gs pcr1c471mcl6gs pcr1c471mcl1gs pcr1c561mcl1gs pcr1c681mcl1gs pcr1c102mcl1gs pcr1d560mcl1gs pcr1d101mcl1gs pcr1d151mcl4gs pcr1d151mcl1gs pcr1d331mcl6gs pcr1d331mcl1gs pcr1d471mcl1gs pcr1d561mcl1gs pcr1d681mcl1gs pcr1e330mcl1gs pcr1e560mcl1gs pcr1e101mcl4gs pcr1e101mcl1gs pcr1e221mcl6gs pcr1e221mcl1gs pcr1e271mcl1gs pcr1e331mcl1gs pcr1e471mcl1gs pcr1v270mcl1gs pcr1v470mcl1gs pcr1v680mcl4gs pcr1v680mcl1gs pcr1v151mcl6gs pcr1v151mcl1gs pcr1v221mcl1gs pcr1v271mcl1gs pcr1v331mcl1gs rated capacitance (f) case size d l (mm) tan part number low temp. esr after endurance (m?) (-40 { c / 100khz) rated ripple (marms) (125 { c / 100khz) initial esr (m?) (20 { c / 100khz) cat.8100c
conductive polymer aluminum solid electrolytic capacitors cr series standard ratings rated voltage (v)(code) surge voltage (v) 600 1000 1300 1300 2900 2200 2900 3000 3500 600 1000 1200 1100 2700 2100 2900 2800 3000 1200 1400 1600 1700 2100 1100 1200 1500 1600 2100 132 75 54 68 39 51 38 38 29 138 77 68 72 42 53 41 42 36 75 57 53 50 42 83 68 63 59 42 88 50 36 45 26 34 25 25 19 92 51 45 48 28 35 27 28 24 50 38 35 33 28 55 45 42 39 28 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 5 6 6.3 6 6.3 8 8 7 8 10 10 8 8 12 10 10 10 12.7 6.3 8 8 10 8 12 10 10 10 12.7 6.3 8 8 10 8 12 10 10 10 12.7 12 22 39 39 82 82 120 120 180 6.8 12 22 22 39 47 56 68 100 12 27 39 47 68 5.6 12 18 22 33 63 50 (1h) 79 63 (1j) 100 80 (1k) 125 100 (2a) pcr1h120mcl1gs pcr1h220mcl1gs pcr1h390mcl4gs pcr1h390mcl1gs pcr1h820mcl6gs pcr1h820mcl1gs pcr1h121mcl2gs pcr1h121mcl1gs pcr1h181mcl1gs pcr1j6r8mcl1gs pcr1j120mcl1gs pcr1j220mcl4gs pcr1j220mcl1gs pcr1j390mcl1gs pcr1j470mcl1gs pcr1j560mcl1gs pcr1j680mcl1gs pcr1j101mcl1gs pcr1k120mcl1gs pcr1k270mcl1gs pcr1k390mcl1gs pcr1k470mcl1gs pcr1k680mcl1gs pcr2a5r6mcl1gs pcr2a120mcl1gs pcr2a180mcl1gs pcr2a220mcl1gs PCR2A330MCL1GS low temp. esr after endurance (m ? ) (-40 { c / 100khz) rated ripple (marms) rated capacitance ( f) case size d l (mm) tan part number initial esr (m ? ) (20 { c / 100khz) rated ripple current (marms) at 125 c 100khz no marked, will be put at 12th digit of type numbering system. 1 : in this case, will be put at 12th digit of type numbering system. 2 : in this case, will be put at 12th digit of type numbering system. 4 : in this case, will be put at 12th digit of type numbering system. 6 taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. cat.8100c
|
